When Does Pipe Wall Thickness Become a Risk in HDD Design?
Understanding Why D/t Ratios Matter in Large-diameter Pipeline Installations
Written by Thomas Wirbicki

Successful HDD projects require more than passing a stress check.
For large-diameter crossings, a steel pipeline can satisfy traditional pullback stress requirements and still be vulnerable to local buckling, ovalization, or external-pressure collapse during installation. These issues can affect constructability, increase uncertainty during execution, and ultimately impact project cost and schedule.
Through the design and evaluation of HDD crossings, trenchless engineers and contractors frequently encounter situations where pipe material may have already been selected or predetermined by others. Drawing on experience supporting HDD projects from feasibility and route evaluation through final design and construction support, these teams help clients identify and address potential risks before they become construction challenges.
One of the most effective ways to identify these risks early is by evaluating the pipe diameter-to-thickness ratio, commonly referred to as D/t. As pipe walls become thinner relative to diameter, stability-related concerns become increasingly important design considerations. Understanding the relevant thresholds allows project teams to proactively evaluate risk, optimize designs, and improve confidence before construction begins.
Why D/t Matters
D/t is the ratio of a pipe’s outside diameter to its wall thickness. Increasing D/t generally means that the pipe wall becomes thinner relative to its diameter, influencing how it responds to installation conditions. For HDD projects, this ratio has a greater impact compared to opencut construction due to the additional stress and strain imposed on the pipe.
Understanding how D/t influences installation performance can help project teams better manage constructability considerations and installation risk through the selection and specification of the pipe.
What Risks Increase as D/t Increases?
+ Local Buckling and Wall Instability
Higher D/t ratios can increase the risk of local buckling, wrinkling, and denting, particularly where bending and axial loads interact during installation. Areas such as drill-path curves, pipe-side overbends, roller-supported sections, and long pullback segments often warrant additional attention.
+ Ovalization During Bending
Thin-walled pipe is more susceptible to ovalization, or cross-sectional flattening, during bending. Excessive ovalization can elevate strain demands and heighten sensitivity to handling and coating damage during installation.
+ Reduced Resistance to External Pressure
As D/t increases, resistance to external-pressure collapse decreases because thinner walls provide less resistance to compressive loading. This becomes particularly important for deep HDD profiles, elevated drilling-fluid pressures, or temporary low-pressure conditions within the carrier pipe, where collapse resistance may become an increasingly important design consideration.
+ Traditional Stress Checks May Not Tell the Full Story
Passing a stress check does not always mean a pipeline is free from installation risk. For higher D/t installations, concerns such as local buckling, ovalization, collapse resistance, and strain performance may require additional evaluation to develop a more complete understanding of constructability and installation behavior.
+ Greater Sensitivity to Construction Variables
Higher D/t pipe often provides less tolerance for real-world construction variables. As a result, factors such as initial ovality, weld mismatch, handling damage, support spacing, and lifting configurations can have a more pronounced impact on installation performance than traditional design calculations alone may suggest.
A Practical Rule of Thumb for HDD Projects
While every HDD crossing should be evaluated based on its unique conditions, D/t can serve as a useful screening tool for pipe selection during preliminary design.
Table 1: Example Wall Thickness at selected D/t ratios for 36-inch-diameter pipe.
| D/t Ratio | Wall Thickness | General Consideration |
| 40 | 0.900 inch | Relatively robust wall for bending and collapse resistance |
| 50 | 0.720 inch | Common screening threshold where enhanced stability review begins |
| 60 | 0.600 inch | Thin-wall behavior becomes increasingly influential |
| 70 | 0.514 inch | High sensitivity; project-specific advanced analysis may be warranted |
As a general guideline:
D/t below 50
Typically provides a comfortable starting point from a constructability and stability perspective, subject to completion of all required HDD design evaluations.
D/t between 50 and 60
Often remains feasible but generally warrants additional attention during design and installation planning.
D/t above 60
Often serves as a design flag for large HDD installations, particularly when crossings involve deep profiles, long pullback distances, tight radii, elevated fluid pressures, or low internal pressure conditions. More detailed strain and stability assessments may be appropriate.

Looking Beyond a Single Number
D/t thresholds such as 50 and 60 are useful indicators, but they should not be viewed as universal acceptance limits. Final pipe wall selection should always be based on project-specific conditions, installation requirements, and code and regulatory compliance for the applicable design criteria.
While these thresholds are useful screening indicators, they do not capture the full range of factors that influence HDD installation performance. Evaluating stability-related considerations alongside traditional stress analyses can provide a more complete understanding of installation risk and support more informed design decisions.
How LSC Evaluates HDD Installation Risk
Understanding project risk often requires more than verifying compliance with standard stress criteria. A complete assessment must consider how installation loads, geometry, drilling-fluid pressures, constructability considerations, and field conditions interact throughout a crossing.
LSC’s trenchless engineering team helps clients evaluate these interactions to better understand constructability risks and support informed design decisions.
Depending on project-specific conditions, our evaluations may include assessments of local buckling potential, ovalization effects, external-pressure collapse resistance, pullback and bending interaction, overbend geometry, and the influence of manufacturing and construction tolerances.
By identifying potential pipe selection challenges early in the design process, project teams can better understand constructability risks, evaluate alternatives, and make informed decisions before construction begins.